Title: Custom CCM Karnivor Sniper
Description: new CCM Karni pump kit!
LudavicoSoldier - October 26, 2008 08:23 PM (GMT)
Finally finished this project with the purchase of the new CCM Karnivor pump kit. Who needs a S6? ;)
WGP two tone black Karnivor body - stock guts
WGP Karni pump front block
CCM 86 slider frame w/Belsales roller sear
CCM Karnivor pump kit
CCM rail
AKA Sidewinder regulator
DYE Ultralite barrel
Belsales delrin bolt
Eclipse OOPS on/off
Eclipse Ego lever lock feed (on custom turned down neck)
Kila magnet detent
22ci Myth'd HPA bottle
Sportshot hopper - modified
fasteddy - October 26, 2008 08:52 PM (GMT)
Pros: Flush cocking rod looks nice.
Cons: You need an A/T !!!
:lol:
LudavicoSoldier - October 26, 2008 09:36 PM (GMT)
Unfortunately, I cant run the CCM AT cam with the WGP detent. The only cams that were made for the slider frames have arms that are too long, since they were designed for the Series 5 bodies, which have wire detents. I may end up going with a CCM 45 frame, and would then use the 86 slider frame on my Ripper project.
Hendie93 - October 26, 2008 09:55 PM (GMT)
Talfuchre - October 26, 2008 11:16 PM (GMT)
| QUOTE (LudavicoSoldier @ Oct 26 2008, 04:36 PM) |
| Unfortunately, I cant run the CCM AT cam with the WGP detent. The only cams that were made for the slider frames have arms that are too long, since they were designed for the Series 5 bodies, which have wire detents. I may end up going with a CCM 45 frame, and would then use the 86 slider frame on my Ripper project. |
I am not sure that makes sense - considering the S6 uses the same AT kit - and a detent cover.
But I am sure you tested it.
TF
LudavicoSoldier - October 26, 2008 11:18 PM (GMT)
That information was direct from Rod at CCM. The flat spot position on the slider frame is different from the hinge frames. I could try to modify the slider cam... The arm on the slider cam is also a bit longer. They redesigned the cam/arm for the swing frames.
Sheazer - October 30, 2008 05:25 PM (GMT)
PumpforLife - November 8, 2008 10:08 PM (GMT)
Looks great, were you able to use a stock length CCM pump rod or did you have to trim it and re-thread it?
STLPlayer007 - November 9, 2008 02:07 AM (GMT)
| QUOTE (LudavicoSoldier @ Oct 26 2008, 06:18 PM) |
| That information was direct from Rod at CCM. The flat spot position on the slider frame is different from the hinge frames. I could try to modify the slider cam... The arm on the slider cam is also a bit longer. They redesigned the cam/arm for the swing frames. |
That is correct. The older slider/hinge frame AT arms are longer. By about 1/10th to 1/8th of an inch.
STL
hichucho - December 2, 2008 04:27 PM (GMT)
I needed a custom AT lever for that same slider trigger. Works nicely, but I hardly ever autotrigger when I play.
LudavicoSoldier - December 2, 2008 10:19 PM (GMT)
I ended up selling off the 86 slider. I am going to pick up a brand new 45 frame and AT rig.
asassin8 - December 12, 2008 03:30 PM (GMT)
i have a 45* slider on my karni, i dont have the at rig tho.... i like it alot. i do like the 86* sliders more but i cant put the snatch grip on the back with those. so i kept the 45*.. your karni looks great!!
good job,
asassin8
