Ok so I explained my situation on the general board.. but I need to plan ahead for some possible financial troubles in the near future.

First thing up for sale:

My MAC-1 Annihilator:

Everything shown is for sale except for the red dot site and the barrel condom:

http://f1.pg.photos.yahoo.com/ph/schmittwe...ide.jpg&.view=t

http://f1.pg.photos.yahoo.com/ph/schmittwe...ide.jpg&.view=t

It has a MAC-1 quick strip bolt and slot in the barrel, quick disconnect installed in side tap, barrel is approx. 12" in length from bolt face and is straight within .0001 of an inch from front to back (german brass tube) Has direct feed and I will include an elbow. Also has pmi hogue type one piece rubber grips and tank ring. 10oz tank and stainless air line and Lapco on/off tank adapter included. Never used on the field on tested in my basement and well maintained.

Looking to get $350 plus shipping

***

Next, my brand new micro stock class phantom with green and silver acid wash ano, 6" barrel, micro pump, ring detents, M-16 grip, and matching ano'd trigger shoe. Brand new in the box, I only fired two rounds through it.

http://f1.pg.photos.yahoo.com/ph/schmittwe...ide.jpg&.view=t

http://f1.pg.photos.yahoo.com/ph/schmittwe...ide.jpg&.view=t

You can have it for what I paid for it, $235 plus shipping.

***

I also have a project pgp that is almost complete (I will have pictures posted later today hopefully) I would be looking for $100 for it. It will have a bucket style quick changer installed parallel to the valve tube on the right side of the gun. for the $100 you get the standard bolt (it will need the ball bearings and spring).

For an extra $30 I will cut a quick strip slot and install a MAC-1 Annihilator quick strip bolt.

The gun will have a new coat of Krylon automotive primer and flat black paint one I've finished work on it. It will need a new front site ( I can install a brass blade for $15 or you can order a bead from BigMatt). It comes with pmi hogue type one piece rubber grips.

Looking for $100 for the basic package plus shipping. Extras as listed I can perform.

***

Project Piranha SB.

I have side tapped the valve. Body has rental numbers etched in two places and is missing the front site. Barrel will need to be honed and polished. Grip frame included but needs safety ball and spring, new grips and probably a paint job. I'm including a new bottomline bracket (no tank asa) and a brand new seal and o-ring pack from palmers.

Looking for $80 plus shipping.

Thanks for looking, I accept pay pal and money orders and you can reach me here or via email.

Hope you can help me out.

Later

Schmitti

Ok the MAC-1 Annihilator finally sold, but I still have the Micro Phantom available for $200 plus shipping if anyone is still interested.

I also have this VM Magnum for sale. I've had this one sitting for a bit and now that I have the VM-EXC M4 all setup, I'm going to let my Magnum go to a new home.

http://f1.pg.photos.yahoo.com/ph/schmittwe....dnm=VM-MAG.jpg

Standard VM magnum with the stock long 1" bull barrel. Most of the body screws have been replaced with stainless steel quick strip screws from Chris Mader. I have replaced the body rails with aluminum rails. The right rail needs some fitting as the hole is just a little off (I haven't had the 5 minutes needed to stick it in the vice on the drill press and adjust the hole, it's about a mm to 2 mm off)

Not pictured. I have installed a Taso bottomline adapter (old school plastic adapter with molded in metal inserts for the screw holes), a beater bottomline adapter (old long duck bill type, with fits almost any straight hole pattern), a gas thru grip in the back asa for some expansion area. Just needs a hose to run from either the gas thru grip to the bottom line or remove the gas thru grip and plumb right into the asa or just screw a tank right in.

Looking for $140 shipped. US continental orders only please otherwise I will get killed on shipping.

I accept paypal or money orders. If you send paypal I can generally ship within a day via USPS priority mail.

The project gun has been kind of parted out, so it's no longer for sale.

Thanks again!

Later!

Schmitti

What!!? They made a 1" barrel for that thing! That's nuts.

Yeah as far as I know it is an inch in diameter. It's 14.5" long and an inch in diameter. I'd seen somebody mention the other day that it's a good thing it wasn't made of brass otherwise the barrel would have weighed as much as the rest of the gun.

Later!

Schmitti

You mean a 1" Outside diameter, no? They were common on old pumps.

Do you still have the Micro Phantom?

Yup I still have the micro phantom, email me if you are interested and we can hash something out. It's all boxed and ready to go, so theoretically you could have it in your hands by monday or tuesday.

Let me know.

Later!

Schmitti

Oh, I thought you meant 1" long.

:lol: At 50 feet you'd get a good, I don't know, 100 inch grouping out of that thing. :P